ABB Power Supplies

ABB SD834

Power Supply Units

Manufacturer: ABB Part Number: SD834

Genuine surplus ABB SD834 power supply, 24 V d.c. 20 A, 480 W, DIN-rail. Verified condition and clear lead times from Autronexa.

  • 12 Month
  • Refurbished
  • In Stock
Call us

Availability & pricing

Pricing is available on request — send an RFQ for a same-day quote.

5-15 days

Technical specifications

Rated output voltage 24 V d.c.
Rated output current 20 A
Rated output power 480 W
Nominal input voltage 100–240 V a.c. / 110–150 V d.c.
Efficiency 92.4/93.9 %
Protection rating IP20 according to IEC 60529
Maximum ambient temperature 55 °C
Dimensions (W × D × H) 82 mm × 127 mm × 124 mm
Weight 1200 g (2.6 lbs.)

Description

When a 24 V control bus drops because a power supply trips its upstream fuse at switch-on, every I/O rack on that segment goes dark. The ABB SD834 power supply addresses exactly that failure mode: a switch-mode unit that converts 100–240 V a.c. or 110–150 V d.c. mains to 24 V d.c. at 20 A, with a soft-start circuit that keeps power-on inrush below 13 A so the supply does not trip a fuse or earth-fault breaker. For maintenance teams replacing a failed unit on a running line, a genuine surplus or refurbished SD834 is often the fastest route back to production.

What This Power Supply Does in a Control Cabinet

This unit is a DIN-rail Class I unit rated 480 W at 24 V d.c., with efficiency stated at 92.4/93.9 %. It accepts both a.c. and d.c. input, which matters where a cabinet is fed from a 110–150 V d.c. battery bus rather than a standard mains feed. The secondary circuit is accepted for SELV and PELV applications, and protective separation keeps the primary side isolated from the secondary. Output is protected against over-current by current limiting and against over-voltage below 37 V. A floating DC-OK relay contact gives a supervision signal, and units can be connected in parallel to raise output power. For redundant arrangements, ABB specifies diode voting units SS823 or SS832. No external mains filter is required for installation.

Figure 1: Front view of the ABB SD834 Power Supply Units showing its physical design and enclosure.

Why Genuine Surplus Fits This Model

Power supplies are among the most frequently replaced items in a cabinet, and This unit is a regularly requested genuine unit in the ABB 800xA and control-system power families. Autronexa stocks surplus and refurbished units that are tested against OEM datasheet specifications and functionally verified by our sourcing team before dispatch. That matters here because the electrical safety basis of this model — EN 50178, EN 61131-2 and UL 508 — is part of its suitability for SELV/PELV circuits; a grey-market substitute with unclear provenance gives you no traceable basis for that claim. Refurbished units also avoid the lead time of ordering new from the OEM when a line is already down. Contact Autronexa with your part number for verified condition and current availability.

Sourcing Checks Before You Order

Confirm the article number 3BSC610067R1 matches the unit you are replacing, and check whether your application is non-redundant or redundant — the latter needs the SS823 or SS832 diode voting unit, which is a separate item. Verify the input feed: nominal 100–240 V a.c. or 110–150 V d.c., with allowed variation of 85–276 V a.c. or 88–187 V d.c. The recommended external primary fuse is 10–20 A. Allow the stated mounting clearances of 15 mm horizontally and 40 mm vertically, and note the 55 °C maximum ambient temperature and IP20 protection rating. Please verify current lifecycle status and availability with Autronexa before ordering.

Frequently asked questions

Is this a genuine ABB SD834, or a clone?

Autronexa verifies each unit against OEM datasheet markings and the article number 3BSC610067R1 before it is listed. We supply genuine surplus and refurbished ABB power supplies, not copies.

What condition will the SD834 arrive in?

Units ship in the condition stated on the listing — our default is refurbished, tested against OEM datasheet specifications and functionally verified by our sourcing team. Confirm the exact condition with Autronexa before ordering.

How fast can you ship the SD834?

Lead time depends on current stock. Contact Autronexa for the current lead time and availability for this part number.

Can the SD834 be used in a redundant configuration?

Yes. ABB specifies diode voting units SS823 or SS832 for redundant applications. These are separate items and are not included with the power supply.

Does the SD834 require an external mains filter?

No. ABB states that no mains filter installation is required with the SD834.

Related & compatible parts

ABB

TU836V1

Genuine surplus ABB TU836V1 ModuleBus MTU with 8 I/O channels, 250 V rated, DIN rail mount. Verified condition…

In Stock

ABB

AI910N

Genuine surplus ABB AI910N analog input module for S900 I/O — 4 channels, 4...20 mA, G3 coating, verified…

In Stock

ABB

DI814

Genuine surplus ABB DI814 digital input module: 16 channels, 24 V d.c., 600 m field cable length. Verified…

In Stock

ABB

AI930B

Genuine surplus ABB AI930B analog input module — 4 channels, 4...20 mA, HART, ATEX Zone 2. Verified condition,…

In Stock

News & guides for ABB

View all articles

Request a quote for this part

Part number: SD834

We reply within one business day.

SD834 Quote reply within 1 business day