Bently Nevada Vibration Monitoring 3500

Bently Nevada 3500/77M 176449-07

3500 System Module

Manufacturer: Bently Nevada Part Number: 3500/77M 176449-07

Bently Nevada 3500/77M 176449-07 3500 System Module. Humidity: 95%, non-condensing; Output Impedance: 550 Ω.

  • Available on request
Call us

Availability & pricing

Pricing is available on request — send an RFQ for a same-day quote.

Technical specifications

Manufacturer Bently Nevada
Product No. 3500/77M 176449-07
Product Type Pressure Monitor
Signal Accepts 1 to 4 channels of Bently Nevada approved positive voltage 3rd-party pressure transducers (psia)
Frequency Response 0 to 5.5 kHz on all configured pressure channels
Cylinder Pressure Discharge Pressure, Suction Pressure, Maximum Pressure, Minimum Pressure, Compression Ratio, Peak Rod Compression, Peak Rod Tension, Degree of Rod Reversal
Input Impedance Internal/External Termination Cylinder Pressure I/O:50 kΩ
Power Consumption 7.8 Watts with transducer supplies at full load.
OK LED Indicates when the 3500/77M is operating properly.
TX/RX LED Indicates when the 3500/77M is communicating with other modules in the 3500 rack.
Bypass LED Indicates when the 3500/77M is in Bypass Mode.
Output Impedance 550 Ω
Transducer Power Supply +23.0 ± 0.8 Vdc with 24.5 ma current limiting on each channel.
Operating Temperature When used with Internal/External Termination Cylinder Pressure I/O Module: -30°C to +65°C (-22°F to +150°F)
Storage Temperature -40°C to +85°C (-40°F to +185°F)
Humidity 95%, non-condensing
Dimensions (Heightx Width x Depth) 241.3 mm x 24.4 mm x241.8 mm (9.50 in x 0.96 in x 9.52in)
Dimensions (Heightx Width x Depth) 241.3 mm x 24.4 mm x99.1 mm (9.50 in x 0.96 in x 3.90in)

Description

The Bently Nevada 3500/77M 176449-07 is a 3500 system module for the 3500 Machinery Protection System. It conditions field transducer signals into vibration and position measurements and compares them against programmable alarm setpoints inside the 3500 rack. and has a nominal power consumption of 7.8 watts with transducer supplies at full load. It monitors critical rotating equipment such as turbines, compressors, and pumps, and communicates monitor status and measured values to the 3500 rack and to recorder outputs for machinery protection. Configuration is performed with 3500 Rack Configuration Software; no field calibration is required.

Product Identification

  • Manufacturer: Bently Nevada.
  • Product No.: 3500/77M 176449-07.
  • Product Type: Pressure Monitor.

Electrical & Signal

  • Input Impedance: Internal/External Termination Cylinder Pressure I/O:50 kΩ.
  • Power Consumption: 7.8 Watts with transducer supplies at full load..
  • Output Impedance: 550 Ω.

Environmental Ratings

  • Operating Temperature: When used with Internal/External Termination Cylinder Pressure I/O Module: -30°C to +65°C (-22°F to +150°F).
  • Storage Temperature: -40°C to +85°C (-40°F to +185°F).
  • Humidity: 95%, non-condensing.

Physical & Mechanical

  • Dimensions (Heightx Width x Depth): 241.3 mm x 24.4 mm x241.8 mm (9.50 in x 0.96 in x 9.52in).
  • Dimensions (Heightx Width x Depth): 241.3 mm x 24.4 mm x99.1 mm (9.50 in x 0.96 in x 3.90in).

Specifications

  • Signal: Accepts 1 to 4 channels of Bently Nevada approved positive voltage 3rd-party pressure transducers (psia).
  • Frequency Response: 0 to 5.5 kHz on all configured pressure channels.
  • Cylinder Pressure: Discharge Pressure, Suction Pressure, Maximum Pressure, Minimum Pressure, Compression Ratio, Peak Rod Compression, Peak Rod Tension, Degree of Rod Reversal.
  • OK LED: Indicates when the 3500/77M is operating properly..
  • TX/RX LED: Indicates when the 3500/77M is communicating with other modules in the 3500 rack..
  • Bypass LED: Indicates when the 3500/77M is in Bypass Mode..
  • Transducer Power Supply: +23.0 ± 0.8 Vdc with 24.5 ma current limiting on each channel..

Model Comparison

Compare the 3500/77M 176449-07 against the closest Bently Nevada configurations below to confirm ordering options, ratings and physical interchange.

Model Product No. OK LED TX/RX LED Output Impedance Signal Bypass LED Transducer Power Supply Product Type
3500/77M 176449-07 3500/77M 176449-07 Indicates when the 3500/77M is operating properly. Indicates when the 3500/77M is communicating with other modules in the 3500 rack. 550 Ω Accepts 1 to 4 channels of Bently Nevada approved positive voltage 3rd-party pressure transducers (psia) Indicates when the 3500/77M is in Bypass Mode. +23.0 ± 0.8 Vdc with 24.5 ma current limiting on each channel. Pressure Monitor
3500/77-03-00 — — — — — — — —
3500/70-01-00 — — — — — — — —
3500/72-01-00 — — — — — — — —
3500/42M 176449-02 176449-02 Indicates when the 3500/42M Proximitor Seismic Monitor is operating properly. Indicates when the 3500/42M Proximitor Seismic Monitor is communicating with other modules in the 3500 rack. 550 Ω Accepts from 1 to 4 proximity, velocity or acceleration transducer signals Indicates when the 3500/42M Proximitor Seismic Monitor is in Bypass Mode. -24 Vdc —
3500/25 149369-01 3500/25 149369-01 Indicates when a fault has been detected in the Keyphasor Module. Indicates when the Keyphasor Module is communicating with the Rack Interface Module (RIM). 504 Ω maximum buffered output impedance. — — — Enhanced Keyphasor Module
3500/42M 140734-02 140734-02 Indicates when the 3500/42M Proximitor Seismic Monitor is operating properly. Indicates when the 3500/42M Proximitor Seismic Monitor is communicating with other modules in the 3500 rack. 550 Ω Accepts from 1 to 4 proximity, velocity or acceleration transducer signals Indicates when the 3500/42M Proximitor Seismic Monitor is in Bypass Mode. -24 Vdc —

Frequently asked questions

What is the Bently Nevada 3500/77M 176449-07 and what does it do?

The Bently Nevada 3500/77M 176449-07 is a component for the 3500 Machinery Protection System. It conditions field transducer signals into vibration and position measurements and compares them against user-programmable alarm setpoints within the 3500 rack.

What is the power consumption of the 3500/77M 176449-07?

The 3500/77M 176449-07 has a nominal power consumption of 7.8 Watts with transducer supplies at full load. It draws power from the 3500 rack backplane and requires no separate supply.

How is the 3500/77M 176449-07 installed and configured?

The 3500/77M 176449-07 mounts in a 3500 rack rear slot and draws power from the rack backplane. Channels are configured with 3500 Rack Configuration Software; alarm setpoints and full-scale ranges are set in software with no field calibration required.

Related & compatible parts

Bently Nevada · 3500

3500/61-05-00

Bently Nevada 3500/61-05-00 Temperature Monitors with Recorder Outputs. Power Consumption: 3500/61 Nominal consumption of 9 watts.

Available on request

Bently Nevada

3500/60-01-00

The Bently Nevada 3500/60 is a Temperature Monitor module for the 3500 system, reading up to six RTD…

Available on request

Bently Nevada

177230-01-01-CN

Bently Nevada 177230-01-01-CN Vibration Monitoring. Measurement Range: 0 – 25.4 mm/s (0 – 1.0 in/s); Diameter: 25.4 mm…

Available on request

Bently Nevada · 3500/40M

129525-0005-02

Bently Nevada 129525-0005-02 Transducer Cable. Cable Length: 5 feet (1.5 metres); Assembly: Not assembled.

Available on request

News & guides for Bently Nevada

View all articles

Request a quote for this part

Part number: 3500/77M 176449-07

We reply within one business day.

3500/77M 176449-07 Quote reply within 1 business day